Commercial · Clermont, FL
Clermont Concreters has served homeowners, HOAs, and commercial sites since 2015, delivering durable concrete curb and gutter work that controls water, protects pavement edges, and tightens up site drainage. In Clermont, FL we build and replace straight runs, returns, curb ramps, driveway aprons, and tie-ins to existing asphalt or concrete with clean grades and consistent reveals.
Good curb and gutter starts below grade. We begin with layout, elevations, and stringline control, then sawcut and demo failing sections and remove soft subgrade. The base is rebuilt with compacted #57 stone or FDOT limerock base as needed, proof-rolled, and tightened to line and grade so the curb does not settle or crack at joints. Where soils are weak or saturated, we stabilize with additional base thickness, geotextile fabric, and proper edge restraint before any concrete is placed.
Central Florida rain and fast runoff make drainage and finish quality matter. We set forms for true flowline, correct cross-slope, and smooth transitions at inlets, curb returns, and driveway crossings, then place 3,500-4,000 psi air-free normal-weight concrete with proper slump for curb forms. Control joints are tooled or sawcut at practical intervals, expansion is installed at tie-ins and structures, and rebar or dowels are used where loads and continuity require it. Finishes are selected for function, including broom-finish on adjacent flatwork, clean edgers on the curb face, and a consistent top radius and gutter pan for predictable water carry.
Clermont customers choose us because we treat curb and gutter like a grading and drainage system, not just a pour. You get clear scope, consistent communication, and crews that know how to hit elevations for stormwater performance while keeping the curb line straight and the gutter smooth. We bring the right equipment for production and accuracy, including skid steer for excavation, plate compactor for base, concrete saws for clean removals and joints, and laser levels for grade control. Whether it is a parking lot edge, a residential drive entrance, or an HOA roadway repair, we focus on long-term serviceability, clean tie-ins, and minimizing disruption to traffic and access.
Before we leave, we walk the run with you and verify line, grade, jointing, and transitions, then set cure time expectations and access limits. You receive a finished curb and gutter that sheds water to the intended inlets, supports pavement edges, and looks uniform from start to finish, including proper joint sealant locations where applicable and tidy cleanup of slurry and debris. We can also coordinate related concrete and site items such as driveway approach panels, sidewalk sections, ADA curb ramps with detectable warning panels when required, and asphalt patch tie-ins. The result is a curb system that performs in heavy rain, resists spalling and settlement, and stays easier to maintain over time.
seo_promise_placeholder
Yes. We can demo and haul off existing slabs, then rebuild the base as needed before forming and pouring new concrete. Disposal and access for equipment are included in the scope when applicable.
Yes. We set forms to match tie-in elevations and establish slope for drainage before placement. Where needed, we dowel into existing concrete and install isolation joints to reduce reflective cracking.
When permits are required, we coordinate the process and schedule inspections. Requirements vary by project type and location, so we confirm this during the site visit.
Common causes include poor base compaction, standing water, rapid drying in heat, inadequate curing, and insufficient joints. Surface flaking (scaling) can also come from finishing mistakes or weak surface paste, which is why placement timing and curing matter.
Often yes, with planning. We schedule around forecasts, protect subgrade from saturation, and avoid placing during active rain that can weaken the surface. If conditions are not right, we reschedule rather than gamble with the finish.
A properly built concrete curb and gutter does more than look finished, it manages stormwater, protects asphalt edges, and helps prevent rutting and erosion along drives, roads, and parking lots. Clermont Concreters installs and replaces curb and gutter for residential, HOA, and commercial properties, with close attention to grading, jointing, and tie-ins so the system carries water where it is supposed to go.
Most curb failures start with base problems, not the concrete itself. We excavate to stable subgrade, remove soft spots, and rebuild the section with compacted #57 stone or limerock base, then set forms to the correct flowline and cross-slope. This keeps the gutter from holding water, reduces undermining at the edge of pavement, and helps the curb line stay straight over time.
For the concrete placement, we use a mix appropriate for exterior flatwork and curb forms, typically 3,500-4,000 psi, placed at workable slump without overwatering. Joints are planned to manage shrinkage cracking, expansion material is installed at structures and transitions, and reinforcement or dowels are added at tie-ins and load areas. Finishing focuses on function and uniform appearance, with clean edges, a consistent top, and a gutter surface that sheds water without birdbaths.
If you are dealing with broken sections, drainage issues, or a new layout for a driveway entrance or parking lot, we can scope the curb run, confirm grades, and recommend the right profile and transitions. You get a clear plan, controlled workmanship, and a concrete curb and gutter system built to perform through Florida rain, traffic, and heat.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Clermont. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.